During the use of marble after decoration, various types of stone rust spots, oil spots, stains and other stains are common. How should marble be cleaned ? Some people will use detergent, detergent, 84 disinfectant, toilet cleaner or other non-stone-specific cleaning agents to clean up. The result is often a lot of effort but no results, even the more ugly, Is the technology wrong or the material wrong? Marble cleaning can not be blind, the following editor will share with you several marble cleaning essentials and marble cleaning and renovation methods and steps.
Marble cleaning 1. Keep it clean
The first step in maintaining stone is to thoroughly remove dust and clean it in time. Before entering the entrance of the house, it is best to put a pad to prevent the dust and gravel outside the house from entering the house, otherwise the sand will follow the footsteps of the person and wear the gloss of the stone surface. It is best to use a vacuum cleaner or an electrostatic mop for dust removal for best results.
Marble cleaning 2. Do not touch non-neutral detergent
Use diluted neutral detergent or clean water to clean the marble. The cleaning products containing improper pH will destroy its luster (especially the acidic detergent can neutralize the calcium carbonate in the stone and make the stone form permanent yellow spots) .
Marble cleaning 3. The source of pollution should be removed immediately
If you accidentally pour the source of pollution (such as oil, tea, coffee, cola, soy sauce, etc.) on the marble, you should wipe it immediately to prevent it from penetrating into the pores and forming an unpleasant stain.
Tips: Once stains are formed, use baking soda and water to spray on the contaminated parts, and then cover them with plastic wrap (sealed with adhesive tape). After a few hours, remove the adhesive tape to clean the residues of the contaminated parts. Dirty effect.
Marble cleaning 4. Prevent the formation of water spots
The marble will not dry for a long time and will always leave wet marks on the surface. This is commonly known as water spot. It can be said that it is very difficult to remove water spots, so for water spots, the only way is to prevent it. There must be no water left on the stone floor. Never wash it directly with water, or mop the floor with a moist moist. Try to blow dry or absorb the cleaned stone floor, too much water will also cause the stone to weather, fall off and float up.
Marble cleaning and renovation
1. Completely clean the ground, use a knife to remove the concrete slurry at the stone gap, and then use a brush or vacuum cleaner to completely remove the dust. Clean it with a dry and clean mop, no sand or impurities on the ground.
2. After the overall cleaning of the stone surface is completed, use marble glue to repair the small damaged points on each stone and the middle seam of the stone. First repair the original damaged surface with marble glue close to the color of the stone. Then use a special stone seaming machine to cut the seam of the original stone installation neatly to make the gap width uniform, and then fill it with marble glue close to the color of the stone. After repairing the marble glue, you must wait for the glue to dry before you can do the next process.
3. After the marble glue is dried, use a sander to polish the whole ground, and then polish the whole ground horizontally. Focus on polishing the caulking glue between the stones and the edges near the walls, decorative shapes, and shaped shapes to keep the overall stone ground flat. After the first pass of polishing, the marble joint is re-run, and the second pass of polishing is continued after the caulking is completed. Then use the stone refurbishment machine to match the steel stone water grinding disc from thick to fine, and it is necessary to complete seven times of grinding. In the end, the whole ground is smooth and smooth. After that, the steel wool is used for polishing, the polishing degree reaches the brightness required by the design, and there is no obvious gap between the stones.
4. After the sanding is completed, use a water absorption machine to treat the water on the ground, and use a blow dryer to dry the entire stone floor. If time permits, you can also use natural air drying to keep the stone surface dry.
5. While spraying the potion evenly on the ground, use a marble polishing machine to grind. Use the cleaning machine with the red scouring pad, sprinkle the potion with the same amount of water on the ground, and start grinding. The effect of the thermal energy makes the crystal surface material crystallize on the surface of the stone.
6. Overall ground maintenance treatment: If the stone with large porosity is to be painted with marble protective agent, it is tossed again to increase the hardness of the crystal surface of the entire ground.
7. Ground cleaning and maintenance: When the stone surface forms a crystal mirror surface, use a vacuum cleaner to absorb residues and moisture on the ground, and finally use a polishing pad to polish, so that the entire ground is completely dry and shiny like a mirror. If local damage is possible, local maintenance can be performed.
Editor's summary: Relevant information on how to do marble cleaning and renovation is introduced here for everyone, I hope this article will be helpful to everyone. No matter how good the marble cleaning method is, it is better to pay more attention to protection in daily life, so everyone should focus on prevention and maintenance, and if necessary, come to a thorough cleaning. If you still do n’t understand something, you can leave a comment below, we will answer it as soon as possible.
What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount
If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.
marble
Pump Water,Aquarium Water Pump,Submersible Water Pump,Electric Water Pump
HENGYUE INDUSTRIAL CO.,LTD , https://www.hetoaquarium.com