Saw blade replacement and adjustment
When replacing the saw blade, first open the upper and lower guard doors, loosen the slide fixing screws, turn the lifting hand wheel to lower the upper saw wheel, loosen the saw blade, take out the old saw blade, and put the ground saw blade on the upper and lower saw wheel, pay attention to the sharp angle of the sawtooth Direction down, do not turn up, then turn the lifting handwheel to raise the upper saw wheel and tighten the saw blade. Then turn the saw wheel by hand to see if the saw teeth are all exposed on the outer side of the saw wheel rim. If it is not exposed, the upper saw wheel should be adjusted until the saw teeth are exposed to the rim, and the edge of the upper and lower saw wheel moves smoothly. Vertical to the work surface.
The tensioning device of the saw blade is divided into two types: spring and compression (heavy hammer). This machine is a spring device. The base tension should be determined according to the width, thickness, and speed of the saw blade. The saw blade is usually pressed by a finger, and the tension of the saw blade is determined according to the left and right curvature of the saw blade. In general, when the saw blade is pressed by hand, the curvature of the saw blade is preferably between 3.2 and 6.4 mm.
The width of the saw blade should be adapted to the width of the saw wheel face and should not exceed the width of the wheel face.
The saw blade is clamped in the middle of the saw clip. The bottom of the saw tooth should be in line with the outer edge of the saw clip. The saw blade cannot be clamped too tightly. It should be able to slide in the middle of the saw clip. There should be a gap on both sides, and the gap on each side is about 0.04~0.08 mm. The back of the saw blade is about 0.8 mm from the pulley. If the saw blade is idling, it will already touch the pulley, that is, the saw blade is behind, or the pulley is forward, or the saw blade is loose. The upper saw wheel or pulley should be adjusted, or the saw blade should be removed. Line inspection
When replacing the saw blade, first open the upper and lower guard doors, loosen the slide fixing screws, turn the lifting hand wheel to lower the upper saw wheel, loosen the saw blade, take out the old saw blade, and put the ground saw blade on the upper and lower saw wheel, pay attention to the sharp angle of the sawtooth Direction down, do not turn up, then turn the lifting handwheel to raise the upper saw wheel and tighten the saw blade. Then turn the saw wheel by hand to see if the saw teeth are all exposed on the outer side of the saw wheel rim. If it is not exposed, the upper saw wheel should be adjusted until the saw teeth are exposed to the rim, and the edge of the upper and lower saw wheel moves smoothly. Vertical to the work surface.
The tensioning device of the saw blade is divided into two types: spring and compression (heavy hammer). This machine is a spring device. The base tension should be determined according to the width, thickness, and speed of the saw blade. The saw blade is usually pressed by a finger, and the tension of the saw blade is determined according to the left and right curvature of the saw blade. In general, when the saw blade is pressed by hand, the curvature of the saw blade is preferably between 3.2 and 6.4 mm.
The width of the saw blade should be adapted to the width of the saw wheel face and should not exceed the width of the wheel face.
The saw blade is clamped in the middle of the saw clip. The bottom of the saw tooth should be in line with the outer edge of the saw clip. The saw blade cannot be clamped too tightly. It should be able to slide in the middle of the saw clip. There should be a gap on both sides, and the gap on each side is about 0.04~0.08 mm. The back of the saw blade is about 0.8 mm from the pulley. If the saw blade is idling, it will already touch the pulley, that is, the saw blade is behind, or the pulley is forward, or the saw blade is loose. The upper saw wheel or pulley should be adjusted, or the saw blade should be removed. Line inspection
Freestanding Plastic Toys,Clear Freestanding Plastic Toy,Outdoor Playground Swing Set,Outdoor Playground With Swings
Zhejiang Egoal Playground Equipment Co., Ltd. , https://www.trampolineparks.pl